Service ManualMicrowave OvenModel : KOC-1B0K0Shttp : //svc.dwe.co.kr Nov. 2000DAEWOO ELECTRONICS CO., LTD.S/M No. : C1B0K0S002✔ Caution: In this Manua
9 (1) Remove the gasket door from door plate. (2) Remove a screw from door plate. (3) Remove the door frame from door plate. (4) Remove the stop
105. To remove control panel parts.REF.NO PART CODE PART NAME DESCRIPTION Q’ TY REMARKB01 3511605000 DECORATOR C-PANEL ABS XR-401 H-2938 1B02 351
11 6. To remove high voltage capacitor. (1) Remove a screw which secure the groun- ding ring terminal of the H.V.diode and the ca
12 8. To remove wind guide assembly.(1) Remove a screw for earthing.(2) Remove the noise filter from the wind guide.(3) Remove a screw which se
1310. To remove Lamp assembly parts.REF.NO PART CODE PART NAME DESCRIPTION Q’ TY REMARK1 7112401011 SCREW TAPPING T1 TRS 4X10 MFZN 12 3512520500 GUI
1411. To remove Top heater assembly parts.REF.NO PART CODE PART NAME DESCRIPTION Q’ TY REMARK1 7112401011 SCREW TAPPING T1 TRS 4X10 MFZN 12 35125205
1512. To remove Rear heater assembly parts.REF.NO PART CODE PART NAME DESCRIPTIONQ’ TYREMARK1 7112401011 SCREW TAPPING T1 TRS 4X10 MFZN 12 351140730
1613. To remove Motor synchro. And Under heater assembly parts.REF.NO PART CODE PART NAME DESCRIPTION Q’ TY REMARK1 7112401011 SCREW TAPPING T1 TRS
177. INTERLOCK MECHANISM AND ADJUSTMENTThe door lock mechanism is a device which has been specially designed to completely eliminatemicrowave radiatio
188. TROUBLE SHOOTING GUIDEFollowing the procedures below to check if the oven is defective or not.1. Check grounding before checking trouble.2. Be ca
1PRECAUTIONS TO BE OBSERVED BEFORE ANDDURING SERVICING TO AVOID POSSIBLEEXPOSURE TO EXCESSIVE MICROWAVE ENERGY(a) Do not operate or allow the oven to
19.Outlet hasPropervoltageFuse doesnot blow?Check continuity ofmagnetronDefectivemagnetron.CONDITION RESULT REMEDYCheck continuity ofnoise filter boar
20.Turn tablemotor andoven lamp donot turn onCheck continuity ofPrimary interlockswitchmalfunctionof primaryinterlock switchCONDITION RESULT REMEDYCh
21 (TROUBLE 6) The Following visual conditions indicate a probable defective touch control Circuit or button P.C.B assembly1. incomplete
22TROUBLE 7) When “ERROR 2 & ERROR 3” come on display.CONDITION CHECK RESULT CAUSE REMEDY“ERROR2 &ERROR3”come ondisplayCheck continuity ofther
239. MEASUREMENT AND TEST9-1. MEASUREMENT OF THE MICROWAVE POWER OUTPUTMicrowave output power can be checked by indirectly measuring the temperature r
249-2. MICROWAVE RADIATION TESTWARNINGl Make sure to check the microwave leakage before and after repair of adjustment.l Always start measuring of an
259-3. COMPONENT TEST PROCEDURE• High voltage is present at the high voltage terminal of the high voltagetransformer during any cooking cycle.• It is
269 -4. COMPONENT ACTIONCOOKING MODEMAGNE-TRONUPPERELEMENTLOWERELEMENTREARELEMENTCONVEC-TION FANM/WGRILL-1GRILL-2GRILL-3COMBI-1COMBI-2COMBI-3COMBI-4CO
2710. WIRING DIAGRAM
2811. EXPLODED VIEW AND PARTS LIST11-1. DOOR ASSEMBLY Refer to 6.Disassembly and assembly.11-2. CONTROL PANEL ASSEMBLY Refer to 6.Disassemb
21. SAFETY AND PRECAUTIONS1. For Safe Operation Damage that allows the microwave energy (that cooks or heats the food) to escape will result in poor
29NO PART CORD PART NAME DESCRIPTION Q'TYA00 3511714000 DOOR AS KOC-1B0K0S 1B00 3516724900 CONTROL PANEL AS KOC-1B0K0S 1F01 3515202200 STOPPER HI
30NO PART CORD PART NAME DESCRIPTION Q'TYF36 3512766800 HARNESS CONVECTION-A KOC-1B0K0S 1F37 3511407700 COVER HEATER *B SA1D T0.5 1F38 3513302900
31NO PART CORD PART NAME DESCRIPTION Q'TYF73 3514801400 SENSOR TEMPERATURE PTM-K312-D7 1F74 3512767000 HARNESS HEATER KOC-1B0K0S 1F75 3517207300
3212. PRINTED CIRCUIT BOARD1. CIRCUIT CHECK PROCEDURE1) Low voltage transformer checkThe low voltage transformer is located on the P.C.B.Measuring co
333) Case of no microwave oscillation(1) When touching M/W button, oven lamp turns on and Fan motor and turntable rotate, and cook indicator in di
344) Case of no heating of upper grill When touching GRILL1 & COMBI button, oven lamp turns on and fan motor and turntable motor rotate and
35STATE POINT A POINT BRELAY 3 ON+5V DC GNDRELAY 3 OFFGND +24V DC7) Case of no stopping of the count do wn timerWhen the door is opened during oper
3613. P.C.B. CIRCUIT DIAGRAM
PCB ASS’ Y PART LIST37NO NAME SYMBOL SPECIFCATION PART CODE Q'TY1 PCB MAIN M223 95.5 X 197 3514322300 12 PCB SUB M224 90 X 197 3514322310 13
32. SPECIFICATIONSMODEL KOC-1B0KPOWER SUPPLY 230V~50Hz, SINGLE PHASE WITH EARTHINGMICROWAVE 1500WGRILL 1600WCONVECTION 2300WPOWERCONSUMPTIONCOMBINATIO
43-2. FEATURE DIAGRAM 1. Door hook – When the door is closed, it will automatically shut. If the door is opened while the oven is operating, the ma
54. INSTALLATION1. Steady, flat location This microwave oven should be set on a steady, flat surface. This microwave oven is designed for counter
65. CONTROL PANEL DISPLAY WINDOW
76. DISASSEMBLY AND ASSEMBLY- Cautions to be observed when trouble shooting.Unlike many other appliances, the microwave oven is high-voltage, high-cur
8A011. To remove cabinet(1) Remove four screws on cabinet back.(2) Push the cabinet backward.2. To remove door assembly(1) Remove two screws which s
Comments to this Manuals